All Outputs (96)

Effect of solar heat flux and thermal loading on the flow distribution within the riser pipes of a closed-loop solar thermo-syphon hot water system. (2015)
Presentation / Conference Contribution
FREEGAH, B., ASIM, T. and MISHRA, R. 2015. Effect of solar heat flux and thermal loading on the flow distribution within the riser pipes of a closed-loop solar thermo-syphon hot water system. In Proceedings of 28th Condition monitoring and diagnostic engineering management international congress 2015 (COMADEM 2015), co-located with 10th regional Congress on non-destructive and structural testing (X CORENDE), 1-4 December 2015, Buenos Aires, Argentina. Birmingham: COMADEM International, pages 398-405.

Solar energy is one of the main sources of renewable energy that is abundantly available throughout the world. Solar energy can be used for useful purposes through a number of mechanical artefacts. One such artefact is known as Thermo-syphon, which t... Read More about Effect of solar heat flux and thermal loading on the flow distribution within the riser pipes of a closed-loop solar thermo-syphon hot water system..

Optimal vaneless diffuser design for a high-end centrifugal compressor. (2015)
Presentation / Conference Contribution
AHMED, N., ASIM, T., MISHRA, R., SIVAGNANASUNDARAM, S. and EYNON, P. 2015. Optimal vaneless diffuser design for a high-end centrifugal compressor. In Proceedings of 28th Condition monitoring and diagnostic engineering management international congress 2015 (COMADEM 2015), co-located with 10th regional Congress on non-destructive and structural testing (X CORENDE), 1-4 December 2015, Buenos Aires, Argentina. Birmingham: COMADEM International, pages 406-413.

Turbochargers are widely used in the automotive industry to reduce engine emissions and to increase the power. Centrifugal compressors are an integral part of turbochargers. Centrifugal compressors comprises primarily of inducer, impeller, diffuser a... Read More about Optimal vaneless diffuser design for a high-end centrifugal compressor..

Drive cycle optimisation for pollution reduction. (2015)
Journal Article
ALGHADHI, M., BALL, A., KOLLAR, L.E., MISHRA, R. and ASIM, T. 2015. Drive cycle optimisation for pollution reduction. International journal of environmental science and development [online], 6(10), pages 727-731. Available from: https://doi.org/10.7763/ijesd.2015.v6.688

Green house gas emissions have abraded environmental quality for human existence. Automobile exhaust is a significant contributor globally to green house gases, among other contributors. This research investigates how vehicle fuel consumption can be... Read More about Drive cycle optimisation for pollution reduction..

Fuel consumption tabulation in laboratory conditions. (2015)
Journal Article
ALGHADHI, M., BALL, A., KOLLAR, L.E., MISHRA, R. and ASIM, T. 2015. Fuel consumption tabulation in laboratory conditions. International research journal of electronics and computer engineering [online], 1(2), pages 10-14. Available from: https://doi.org/10.24178/irjece.2015.1.2.10

Environmental degradation has come about for a number of factors including the use of fossil fuels in vehicles for everyday use. This paper attempts to understand the relationship between fuel consumption and various engine performance parameters und... Read More about Fuel consumption tabulation in laboratory conditions..

Fire safety analysis of a railway compartment using computational fluid dynamics. (2015)
Journal Article
ENBAYA, A., ASIM, T., MISHRA, R. and RAO, R.B.K.N. 2015. Fire safety analysis of a railway compartment using computational fluid dynamics. International journal of COMADEM [online] 18(3), pages 37-44. Available from: http://www.comadem.com/journal/past-issues/

Trains are considered to be the safest on land transportation for both passengers and cargo. Train accidents have been disastrous especially in case of fire, where the consequences results in loss of life and goods. The fire would generate smoke and... Read More about Fire safety analysis of a railway compartment using computational fluid dynamics..

Numerical investigations on the effect of blade angles of a vertical axis wind turbine on its performance output. (2015)
Journal Article
PARK, K.-S., ASIM, T. and MISHRA, R. Numerical investigations on the effect of blade angles of a vertical axis wind turbine on its performance output. International journal of condition monitoring and diagnostic engineering management (COMADEM) [online], 18(3), pages 3-10. Available from: http://www.comadem.com/journal/past-issues/

There are many social, political and environmental issues associated with the use of fossil fuels. For this reason, there are numerous investigations currently being carried out to develop newer and renewable sources of energy to alleviate energy dem... Read More about Numerical investigations on the effect of blade angles of a vertical axis wind turbine on its performance output..

Drive cycle optimisation for pollution reduction. (2015)
Presentation / Conference Contribution
AL-GHADHI, M., BALL, A., KOLLAR, L.E., MISHRA, R. and ASIM, T. 2015. Drive cycle optimisation for pollution reduction. Presented at 2nd International conference on petroleum and petrochemical engineering 2015 (ICPPE 2015), 10-11 January 2015, Dubai, UAE.

Green house gas emissions have abraded environmental quality for human existence. Automobile exhaust is a significant contributor globally to green house gases, among other contributors. This research investigates how vehicle fuel consumption can be... Read More about Drive cycle optimisation for pollution reduction..

The effect of blade angles of the vertical axis wind turbine on the output performance. (2014)
Presentation / Conference Contribution
MOHAMED, F., PARK, K.-S., PRADHAN, S., MISHRA, R., ZALA, K., ASIM, T. and AL-OBAIDI, A. 2014. The effect of blade angles of the vertical axis wind turbine on the output performance. Presented at 27th Condition monitoring and diagnostic engineering management international congress 2014 (COMADEM 2014), 16-18 September 2014, Brisbane, Australia.

There are many social, political and environmental issues associated with the use of fossil fuels. For this reason, there are numerous investigations currently being carried out to develop newer and renewable sources of energy to alleviate energy dem... Read More about The effect of blade angles of the vertical axis wind turbine on the output performance..

Numerical studies of the velocity distribution within the volute of a centrifugal pump. (2014)
Presentation / Conference Contribution
AL-OBAIDI, A., PRADHAN, S., ASIM, T., MISHRA, R. and ZALA, K. 2014. Numerical studies of the velocity distribution within the volute of a centrifugal pump. Presented at 27th Condition monitoring and diagnostic engineering management international congress 2014 (COMADEM 2014), 16-18 September 2014, Brisbane, Australia.

Centrifugal pumps play an essential role in engineering systems since they are widely used in the process and power industries. The performance of a centrifugal pump needs to be maximised due to its importance and this depends on the flow structure w... Read More about Numerical studies of the velocity distribution within the volute of a centrifugal pump..

Effect of the shape of connecting pipes on the performance output of a closed-loop hot water solar Thermo-syphon. (2014)
Presentation / Conference Contribution
FREEGAH, B., ASIM, T., ALBARZENJI, D., PRADHAN, S. and MISHRA, R. 2014. Effect of the shape of connecting pipes on the performance output of a closed-loop hot water solar Thermo-syphon. In Kumar, U., Karim, R., Parida, A. and Tretten, P. (eds.) Proceedings of 3rd international workshop and congress on eMaintenance: eMaintenance, trends in technologies and methodologies, challenges, possibilities and applications, 17-18 June 2014, Luleå, Sweden. Luleå: Luleå University of Technology [online], pages 119-123. Available from: http://ltu.diva-portal.org/smash/record.jsf?pid=diva2%3A997766&dswid=-1615

In order to conserve the environment from pollution, which is caused by the use of the fossil fuels, numerous research works have been carried out in renewable energy area to minimize the dependency on the fossil fuels. There are several energy sourc... Read More about Effect of the shape of connecting pipes on the performance output of a closed-loop hot water solar Thermo-syphon..

Fuel consumption tabulation in laboratory conditions. (2014)
Presentation / Conference Contribution
ALGHADHI, M., BALL, A., KOLLAR, L.E., MISHRA, R. and ASIM, T. 2014. Fuel consumption tabulation in laboratory conditions. International journal of recent development in engineering and technology [online], 2(Special issue 4): papers from 2014 International research conference on engineering, science and management (IRCESM 2014), 4-5 June 2014, Dubai, UAE, pages 29-38. Available from: https://www.ijrdet.com/files/IRCESM2014/IJRDET_IRCESM_05.pdf

This paper examines the fuel economy displayed by passenger vehicles and attempts to connect vehicular fuel consumption to such easily measurable parameters as vehicle speed, acceleration, gear and throttle position. The central contention is to unde... Read More about Fuel consumption tabulation in laboratory conditions..

Numerical analysis of atherosclerosis and aneurysm in carotid bifurcations using computational fluid dynamics. (2013)
Presentation / Conference Contribution
ASIM, T., SENDANAYAKE, I. and MISHRA, S. 2013. Numerical analysis of atherosclerosis and aneurysm in carotid bifurcations using computational fluid dynamics. Presented at 40th National conference on fluid mechanics and fluid power 2013 (NCFMFP 2013), 12-14 December 2013, Hamirpur, India.

Atherosclerosis and Aneurysm are some of the conditions in patients suffering from vascular diseases. These vascular defects can cause severe damage to cardiovascular system (CVS), if not properly diagnosed. The advent of advanced numerical and compu... Read More about Numerical analysis of atherosclerosis and aneurysm in carotid bifurcations using computational fluid dynamics..

Effects of a moving surface boundary layer control device (MSBC) on the drag reduction in heavy commercial vehicles. (2013)
Presentation / Conference Contribution
ASIM, T., SENDANAYAKE, I., MISHRA, R., ZALA, K. and UBBI, K. 2013. Effects of a moving surface boundary layer control devise (MSBC) on the drag reduction in heavy commercial vehicles. Presented at 40th National conference on fluid mechanics and fluid power 2013 (NCFMFP 2013), 12-14 December 2013, Hamirpur, India.

Rapid escalation in fuel prices has motivated the manufacturers of heavy commercial vehicles to focus their attention towards efficient aerodynamic design of surface transport systems such as trucks–trailers, railways etc. In order to reduce the drag... Read More about Effects of a moving surface boundary layer control device (MSBC) on the drag reduction in heavy commercial vehicles..

Numerical analysis of a closed thermo-syphon hot water solar system under steady and transient loading conditions. (2013)
Presentation / Conference Contribution
FREEGAH, B., ASIM, T., and MISHRA, R. 2013. Numerical analysis of a closed thermo-syphon hot water solar system under steady and transient loading conditions. Presented at 40th National conference on fluid mechanics and fluid power 2013 (NCFMFP 2013), 12-14 December 2013, Hamirpur, India.

Solar energy is one of the most important sources of alternative energy. This energy source is inexhaustible and the cleanest of all known energy sources. One of the most important systems which can be used to exploit energy stored in the solar rays... Read More about Numerical analysis of a closed thermo-syphon hot water solar system under steady and transient loading conditions..

Particle size effects on optimal sizing and lifetime of pipelines transporting multi-sized solid-liquid mixtures. (2013)
Presentation / Conference Contribution
KOLLÁR, L.E., MISHRA, R. and ASIM, T. 2013. Particle size effects on optimal sizing and lifetime of pipelines transporting multi-sized solid-liquid mixtures. Procedia CIRP [online], 11: proceedings of 2nd Through-life engineering services international conference 2013 (TESConf 2013), 5-6 November 2013, Cranfield, UK, pages 317-322. Available from: https://doi.org/10.1016/j.procir.2013.07.008

A life-cycle cost analysis model is developed in this study, to examine the effects of particle size distribution of the solid particles to be transported on the optimal sizing and lifetime of the pipelines used for transportation of solid-liquid mix... Read More about Particle size effects on optimal sizing and lifetime of pipelines transporting multi-sized solid-liquid mixtures..

Performance of a vertical axis wind turbine under accelerating and decelerating flows. (2013)
Presentation / Conference Contribution
SHAHZAD, A., ASIM, T., MISHRA, R. and PARIS, A. 2013. Performance of a vertical axis wind turbine under accelerating and decelerating flows. Procedia CIRP [online], 11: proceedings of 2nd Through-life engineering services international conference 2013 (TESConf 2013), 5-6 November 2013, Cranfield, UK, pages 311-316. Available from: https://doi.org/10.1016/j.procir.2013.07.006

Rapid increase in global energy requirements has resulted in considerable attention towards energy generation from the renewable energy sources. In order to meet renewable energy targets, harnessing energy from all available resources including those... Read More about Performance of a vertical axis wind turbine under accelerating and decelerating flows..

Computational fluid dynamics based optimal design of vertical axis marine current turbines. (2013)
Presentation / Conference Contribution
ASIM, T., MISHRA, R., UBBI, K. and ZALA, K. 2013. Computational fluid dynamics based optimal design of vertical axis marine current turbines. Procedia CIRP [online], 11: proceedings of 2nd Through-life engineering services international conference 2013 (TESConf 2013), 5-6 November 2013, Cranfield, UK, pages 323-327. Available from: https://doi.org/10.1016/j.procir.2013.07.023

Marine turbines are being increasingly used to harness kinetic energy of water and convert it into other useful forms of energy. Widespread commercial acceptability of these machines depends upon their efficiency. This largely depends upon the geomet... Read More about Computational fluid dynamics based optimal design of vertical axis marine current turbines..

Optimal design methodology for on-shore hydraulic pipelines transporting spherical capsules. (2013)
Presentation / Conference Contribution
ASIM, T., MISHRA, R., PARIS, A. and ZALA, K. 2013. Optimal design methodology for on-shore hydraulic pipelines transporting spherical capsules. Procedia CIRP [online], 11: 2nd Through-life engineering services international conference 2013 (TESConf 2013), 5-6 November 2013, Cranfield, UK, pages 305-310. Available from: https://doi.org/10.1016/j.procir.2013.07.010

The third generation of pipelines comprises of the transportation of capsules that are hollow, water-borne containers, usually spherical or cylindrical in shape, filled with goods. These capsules are transported within pipelines along with the fluid,... Read More about Optimal design methodology for on-shore hydraulic pipelines transporting spherical capsules..

Effect of the shape of stator blades on the performance output of a vertical axis marine current turbine. (2013)
Presentation / Conference Contribution
ASIM, T., MISHRA, R. and UBBI, K.S. 2013. Effect of the shape of stator blades on the performance output of a vertical axis marine current turbine. In Proceedings of 26th Condition monitoring and diagnostic engineering management international congress 2013 (COMADEM 2013), 11-­13 June 2013, Helsinki, Finland. Birmingham: COMADEM International.

Due to the diminishing reserves of fossil fuels and increased pollution from exploitation of these fuels, the world is focusing on the renewable energy sources. Energy from tidal waves is one of the most exciting forms of renewable energy because of... Read More about Effect of the shape of stator blades on the performance output of a vertical axis marine current turbine..

Computational fluid dynamics based analysis of a closed thermo-siphon hot water solar system. (2013)
Presentation / Conference Contribution
FREEGAH, B., ASIM, T. and MISHRA, R. 2013. Computational fluid dynamics based analysis of a closed thermo­siphon hot water solar system. In Proceedings of 26th Condition monitoring and diagnostic engineering management international congress 2013 (COMADEM 2013), 11-­13 June 2013, Helsinki, Finland. Birmingham: COMADEM International.

One of the alternative sources of energy is solar energy which is available in abundance throughout the world. The energy contained within the solar rays is capable of starting natural convection within closed mechanical systems containing a suitable... Read More about Computational fluid dynamics based analysis of a closed thermo-siphon hot water solar system..