Browse

Reactive power minimization of dual active bridge DC/DC converter with triple phase shift control using neural network. (2014)
Conference Proceeding
HARRYE, Y.A., AHMED, K.H. and ABOUSHADY, A.A. 2014. Reactive power minimization of dual active bridge DC/DC converter with triple phase shift control using neural network. In Proceedings of the 3rd International conference on renewable energy research and applications (ICRERA 2014), 19-22 October 2014, Milwakuee, USA. Piscataway: IEEE [online], pages 566-571. Available from: https://doi.org/10.1109/ICRERA.2014.7016448

Reactive power flow increases dual active bridge (DAB) converter RMS current leading to an increase in conduction losses especially in high power applications. This paper proposes a new optimized triple phase shift (TPS) switching algorithm that mini... Read More about Reactive power minimization of dual active bridge DC/DC converter with triple phase shift control using neural network..

Rotationally asymmetrical compound parabolic concentrator for concentrating photovoltaic applications. (2014)
Journal Article
ABU-BAKAR, S.H., MUHAMMAD-SUKKI, F., RAMIREZ-INIGUEZ, R., MALLICK, T.K., MUNIR, A.B., YASIN, S.H.M. and RAHIM, R.A. 2014. Rotationally asymmetrical compound parabolic concentrator for concentrating photovoltaic applications. Applied energy [online], 136, pages 363-372. Available from: https://doi.org/10.1016/j.apenergy.2014.09.053

This paper describes a novel type of solar concentrator - a rotationally asymmetrical compound parabolic concentrator (RACPC). The RACPC aims at addressing the following objectives: (i) to increase the electrical output of a concentrating photovoltai... Read More about Rotationally asymmetrical compound parabolic concentrator for concentrating photovoltaic applications..

Cold heavy oil production using CO2-EOR technique. (2014)
Thesis
TCHAMBAK, E.N. 2014. Cold heavy oil production using CO2-EOR technique. Robert Gordon University, PhD thesis.

This thesis presents results of a successful simulation study using the CO2-EOR technique to enable production from an offshore heavy oil field, named here as Omega, which is located offshore West Africa at a water depth around 2000 m. The findings a... Read More about Cold heavy oil production using CO2-EOR technique..

Rheological behaviour of single-phase non-Newtonian polymer solution in complex pore geometry: a simulation approach. (2014)
Conference Proceeding
IDAHOSA, P., OLUYEMI, G., PRABHU, R. and OYENEYIN, B. 2014. Rheological behaviour of single-phase non-Newtonian polymer solution in complex pore geometry: a simulation approach. In Proceedings of the 2014 COMSOL conference, 17-19 September 2014, Cambridge, UK. Burlington: COMSOL [online], article ID 18685. Available from: https://www.comsol.com/paper/rheological-behaviour-of-single-phase-non-newtonian-polymer-solution-in-complex--18685

One of the most important criteria for evaluating chemical enhanced oil recovery (EOR) processes that use polymers is its rheological behaviour which in turn account for other physical effects of adsorption and resistance factors during polymer-rock... Read More about Rheological behaviour of single-phase non-Newtonian polymer solution in complex pore geometry: a simulation approach..

The effect of blade angles of the vertical axis wind turbine on the output performance. (2014)
Presentation / Conference
MOHAMED, F., PARK, K.-S., PRADHAN, S., MISHRA, R., ZALA, K., ASIM, T. and AL-OBAIDI, A. 2014. The effect of blade angles of the vertical axis wind turbine on the output performance. Presented at 27th Condition monitoring and diagnostic engineering management international congress 2014 (COMADEM 2014), 16-18 September 2014, Brisbane, Australia.

There are many social, political and environmental issues associated with the use of fossil fuels. For this reason, there are numerous investigations currently being carried out to develop newer and renewable sources of energy to alleviate energy dem... Read More about The effect of blade angles of the vertical axis wind turbine on the output performance..

Numerical studies of the velocity distribution within the volute of a centrifugal pump. (2014)
Presentation / Conference
AL-OBAIDI, A., PRADHAN, S., ASIM, T., MISHRA, R. and ZALA, K. 2014. Numerical studies of the velocity distribution within the volute of a centrifugal pump. Presented at 27th Condition monitoring and diagnostic engineering management international congress 2014 (COMADEM 2014), 16-18 September 2014, Brisbane, Australia.

Centrifugal pumps play an essential role in engineering systems since they are widely used in the process and power industries. The performance of a centrifugal pump needs to be maximised due to its importance and this depends on the flow structure w... Read More about Numerical studies of the velocity distribution within the volute of a centrifugal pump..

A low complexity visual saliency model based on in-focus regions and centre sensitivity. (2014)
Conference Proceeding
CHILUKAMARI, J., KANNANGARA, S. and MAXWELL, G. 2014. A low complexity visual saliency model based on in-focus regions and centre sensitivity. In Proceedings of the 4th IEEE international conference on consumer electronics (ICCE-Berlin 2014), 7-10 September 2014, Berlin, Germany. New York: IEEE [online], article number 7034250, pages 411-414. Available from: https://doi.org/10.1109/ICCE-Berlin.2014.7034250

A novel low-complexity visual saliency detection algorithm for detecting salient regions in images is proposed. The algorithm derives salient regions based on in-focus regions and image centre sensitivity. The performance of the algorithm in predicti... Read More about A low complexity visual saliency model based on in-focus regions and centre sensitivity..

Five principles for the practice of knowledge exchange in environmental management. (2014)
Journal Article
REED, M.S., STRINGER, L.C., FAZEY, I., EVELY, A.C. and KRUIJSEN, J.H.J. 2014. Five principles for the practice of knowledge exchange in environmental management. Journal of environmental management [online], 146, pages 337-345. Available from: https://doi.org/10.1016/j.jenvman.2014.07.021

This paper outlines five principles for effective practice of knowledge exchange, which when applied, have the potential to significantly enhance the impact of environmental management research, policy and practice. The paper is based on an empirical... Read More about Five principles for the practice of knowledge exchange in environmental management..

Purification of gases using nanoporous inorganic membranes. (2014)
Journal Article
KAJAMA, M.N., SHEHU, H. and GOBINA, E. 2014. Purification of gases using nanoporous inorganic membranes. International journal of scientific engineering and technology [online], 3(9), pages 1156-1159. Available from: https://www.ijset.com/publication/v3/262.pdf

The application of membranes has gained acceptance in the chemical and process industries for separation and purification for over three decades and is currently being practiced for natural gas processing, waste water treatment among others. A crack-... Read More about Purification of gases using nanoporous inorganic membranes..

Integration of gas transport through a composite catalytic inorganic ceramic membrane for environmental gas separation processes. (2014)
Journal Article
NWOGU, N., OKON, E. and GOBINA, E. 2014. Integration of gas transport through a composite catalytic inorganic ceramic membrane for environmental gas separation processes. International journal of scientific engineering and technology [online], 3(9) pages 1184-1188. Available from: http://ijset.com/publication/v3/268.pdf

This work presents the transport behaviour of carrier gases with inorganic ceramic membrane used for environmental gas separations at 289K and 0.01-1 bar. The gases tested include: Helium (He), Nitrogen (N2), Carbon dioxide (CO2) and Argon (AR). The... Read More about Integration of gas transport through a composite catalytic inorganic ceramic membrane for environmental gas separation processes..

Investigations on surface wettability of ZnO nanowires using UV LEDs for biosensing applications. (2014)
Journal Article
BHAVSAR, K., PRABHU, R. and POLLARD, P. 2014. Investigations on surface wettability of ZnO nanowires using UV LEDs for biosensing applications. IOP conference series: materials science and engineering [online], 64, Article 012033. Available from: https://doi.org/10.1088/1757-899X/64/1/012033

ZnO is a biocompatible material suitable for biosensors and microfluidic devices. Nanowires of ZnO tend to show hydrophobic nature which decelerates the adhesion/adsorption of biomolecules on the surface. This paper discusses the investigations on tu... Read More about Investigations on surface wettability of ZnO nanowires using UV LEDs for biosensing applications..

Highly transparent and luminescent nanostructured Eu203 doped ZnO films. (2014)
Journal Article
SREEDHARAN, R.S., GANASAN, V., SUDARSANAKUMAR, C., PRABHU, R. and PILLAI, V.P.M., 2014. Highly transparent and luminescent nanostructured Eu203 doped ZnO films. IOP conference series: materials science and engineering [online], 64, Article 012027. Available from: https://doi.org/10.1088/1757-899X/64/1/012027

Zinc oxide is a wide, direct band gap II-VI oxide semiconductor. Pure and Eu-doped ZnO films are prepared by RF Magnetron sputtering at different doping concentrations (0.5, 1, 3 and 5 wt %). The films are annealed at 500 0C in air for two hours. The... Read More about Highly transparent and luminescent nanostructured Eu203 doped ZnO films..

Characterization of synthesized polyurethane/montmorillonite nanocomposite foams. (2014)
Journal Article
ANSARI, F., SACHSE, S., MICHALOWSKI, S., KAVOSH, M., PIELICHOWSKI, K. and NJUGUNA, J. 2014. Characterization of synthesized polyurethane/montmorillonite nanocomposite foams. IOP conference series: materials science and engineering [online], 64(1), Article 012039. Available from: https://doi.org/10.1088/1757-899X/64/1/012039

Nanophased hybrid composites based on polyurethane/montmorillonite (PU/MMT) have been fabricated. The nanocomposite which was formed by the addition of a polyol premix with 4,4'-diphenylmethane diisocyanate to obtain nanophased polyurethane foams whi... Read More about Characterization of synthesized polyurethane/montmorillonite nanocomposite foams..

A review on the effect of mechanical drilling on polymer nanocomposites. (2014)
Journal Article
STAROST, K. and NJUGUNA, J. 2014. A review on the effect of mechanical drilling on polymer nanocomposites. IOP conference series: materials science and engineering [online], 64(1), Article 012031. Available from: https://doi.org/10.1088/1757-899X/64/1/012031

Over the past decade, polymer nanocomposites have undergone intensive research and development ensued by its increasing implementation within commercial applications. Consequently, the full life-cycle performance and any health risks associated with... Read More about A review on the effect of mechanical drilling on polymer nanocomposites..

Waste to want: polymer nanocomposites using nanoclays extracted from oil based drilling mud waste. (2014)
Journal Article
ADEGBOTOLU, U.V., NJUGUNA, J., POLLARD, P. and YATES, K. 2014. Waste to want: polymer nanocomposites using nanoclays extracted from oil based drilling mud waste. IOP conference series: materials science and engineering [online], 64, Article 012023. Available from: https://doi.org/10.1088/1757-899X/64/1/012023

Due to the European Union (EU) waste frame work directive (WFD), legislations have been endorsed in EU member states such as UK for the Recycling of wastes with a vision to prevent and reduce landfilling of waste. Spent oil based drilling mud (drilli... Read More about Waste to want: polymer nanocomposites using nanoclays extracted from oil based drilling mud waste..

Compression-after-impact (CAI) performance of epoxycarbon fibre-reinforced nanocomposites using nanosilica and rubber particle enhancement. (2014)
Journal Article
NIKFAR, B. and NJUGUNA, J. 2014. Compression-after-impact (CAI) performance of epoxycarbon fibre-reinforced nanocomposites using nanosilica and rubber particle enhancement. IOP conference series: materials science and engineering [online], 64(1), Article 012009. Available from: https://doi.org/10.1088/1757-899X/64/1/012009

One of the problems in the design of automotive structures and body parts made by fibre reinforced composites is that these materials are susceptible to a small energy impact caused by for instance, accidental tool drop during maintenance or stone st... Read More about Compression-after-impact (CAI) performance of epoxycarbon fibre-reinforced nanocomposites using nanosilica and rubber particle enhancement..

Experimental study of gas flux characteristics in a CO2 selective silica based modified membrane. (2014)
Journal Article
NWOGU, N.C., KAJAMA, M.N. and GOBINA, E. 2014. Experimental study of gas flux characteristics in a CO2 selective silica based modified membrane. International journal of advanced research in engineering and technology (IJARET) [online], 5(8), pages 1-9. Available from: http://www.iaeme.com/MasterAdmin/Journal_uploads/IJARET/VOLUME_5_ISSUE_8/IJARET_05_08_001.pdf

The purpose of membrane gas separation for CO2 capture from flue gas process is to reduce greenhouse emissions as well as associated environmental challenges globally. This study looks at gas separation in a single gas permeation experiment using CO2... Read More about Experimental study of gas flux characteristics in a CO2 selective silica based modified membrane..

Mechanical and impact performance of three-phase polyamide 6 nanocomposites. (2014)
Journal Article
GENDRE, L., NJUGUNA, J., ABHYANKAR, H. and ERMINI, V. 2015. Mechanical and impact performance of three-phase polyamide 6 nanocomposites. Materials and design [online], 66(Part B), pages 486-491. Available from: https://doi.org/10.1016/j.matdes.2014.08.005

In this work, three-phase nanocomposites using multiscale reinforcements were studied to evaluate the influence of nanofillers on static and dynamic mechanical properties at varying temperature conditions. In particular, short-fibres reinforced polya... Read More about Mechanical and impact performance of three-phase polyamide 6 nanocomposites..

Too enthusiastic to care for safety: present status and recent developments of nanosafety in ASEAN countries. (2014)
Journal Article
KARIM, M.E., MUNIR, A.B., REZA, A.W., MUHAMMAD-SUKKI, F., YASIN, S.H.M., ABU-BAKAR, S.H. and RAHIM, R.A. 2015. Too enthusiastic to care for safety: present status and recent developments of nanosafety in ASEAN countries. Technological forecasting and social change [online], 92, pages 168-181. Available from: https://doi.org/10.1016/j.techfore.2014.07.003

Nanotechnology has the prospect to vibrate the imagination of human being and has the ability to be used in almost every sector of human need. With its limitless potentials, there are many environmental, health and safety related concerns due to extr... Read More about Too enthusiastic to care for safety: present status and recent developments of nanosafety in ASEAN countries..

Significance of effective lubrication in mitigating system failures: a wind turbine gearbox case study. (2014)
Journal Article
SINHA, Y., STEEL, J.A., ANDRAWUS, J.A. and GIBSON, K. 2014. Significance of effective lubrication in mitigating system failures: a wind turbine gearbox case study. Wind engineering [online], 38(4), pages 441-449. Available from: https://doi.org/10.1260/0309-524x.38.4.441

The effectiveness of lubrication in machines mainly depends on the physical and chemical properties of lubricating oil, like quantity, level of suspended particles, effect of external load/shear forces, temperature amongst others. Periodic inspection... Read More about Significance of effective lubrication in mitigating system failures: a wind turbine gearbox case study..